Home and Family idea

Install Wall-to-Wall Carpeting
Install Wall-to-Wall Carpeting -2
Install Wall-to-Wall Carpeting -3

When all the padding has been set into position, trim off the edges overlapping the fastening strips. Use a utility knife with a sharp heavy-duty blade to trim the excess padding; holding the knife at an angle toward you, cut the padding off exactly where it meets the inside edge of the fastening strips. The surface of the padding should be more or less level with the surface of the fastening strips.

Finally, unroll the carpeting over the padding and pull it carefully into position, overlapping the fastening strips all around the room. Slit the folded-up carpeting vertically where it goes around corners, being careful not to cut past the overlap into the main carpet, so that the edges lie flat against both corner walls. Make straight cuts and crosscuts to fit the carpeting around radiators and other obstructions; don’t cut holes in the carpet to accommodate them. Trim carefully around open floor registers, leaving a slight overlap.

Attach the carpeting to the fastening strips with the knee kicker. Starting in a corner, set the head of the kicker flat on the carpet, about an inch from the wall and aimed slightly down and at an angle to the wall. Kneeling on the floor at the corner, hold the handle of the kicker with one hand and lean on the floor with the other. Put all your weight on the knee opposite the arm holding the kicker and move your other knee forward sharply to hit the cushioned end of the kicker. The head of the kicker will stretch the carpeting under it to hook it’ onto the teeth of the fastening strip at the edge of the floor, leaving an untrimmed edge of carpeting still sticking up against the wall. Repeat the kicking process to fasten the carpeting on the opposite wall of the corner.

After kicking the first corner of the room into place, fasten the two adjacent corners the same way, leaving the diagonally opposite corner loose. Then work from your starting corner out along the two walls of the corner, holding the just-fastened carpeting in place with one hand and using the other to kick the next few inches of carpeting. Make sure the carpeting lies flat and doesn’t shift as you work. Fasten the third side of the carpet, working toward the loose corner, and then fasten the fourth side.

Use a utility knife with a sharp heavy-duty blade to trim the edges of the carpeting, and replace the blade as soon as it begins to dull. Cut off the turned-up edge of carpeting evenly, leaving about 3/8 inch still sticking up above the tacked-down edge. Cut carefully, and snip off any ragged tufts of yarn.

To complete the installation, use a stiff putty knife to wedge the trimmed edge of the carpeting down into the ¼  -inch gap between the walls and the fastening strips. Press the cut edge of the carpeting firmly into place all around the room. To finish the edge at doorways, trim the carpet edge carefully to fit under the curved rim of the door finishing strip. Push the raw carpet edge under the rim and use a hammer and a wood block to pound the rim firmly down over the carpet edge.

Finally, replace floor registers-you may have to trim the carpet edge back farther, but cut carefully. Replace quarter-round baseboard molding if you removed it earlier, and rehang the doors. If the new carpeting and padding are much thicker than the old floor covering, you’ll probably have to plane the bottom edge of each door so it can open and close easily. Remove the door from its hinges and plane the bot’ tom edge carefully, planing from both ends toward the center. Rehang the door. Move the furniture back into the room.

When all the fastener strips have been nailed into place, take the rolled-up carpeting and pull it into position in the room and unroll it, right over the bare floor. This is so you won’t jerk the padding out of place later by pulling the carpeting across it. Roll the carpet¬ing back from one side toward the cen¬ter of the room, exposing the floor again.

Unroll a strip of foam padding along the edge of the floor across the bare side of the room from wall to wall, waffle-patterned side up. Cut the strip carefully with heavy scissors, leaving about 2 inches overlapping the fastening strips at each end. Pull the strip to position it over the bare end of the floor so that it overlaps the fastening strips on both ends and along the wall. Then staple it into place, using a staple gun to set staples diagonally every 6 inches or so along all four edges of the padding. Cover the rest of the room the same way, rolling the carpeting back so you can roll the padding into place. Butt the edges of the strips of padding and staple every 6 inches along every edge. Trim the padding as necessary to fit around obstacles, cutting as closely as possible around them.

Read More…

Before installing the carpeting, pre¬pare the floor. Move all furniture out of the room and remove doors that open into the room. Pound in any loose nails and reset squeaky floorboards with flooring nails, using a nail set to drive the heads below the floor surface. Condensation can be a problem when resilient flooring is carpeted; if the floor is covered with resilient tile or sheet flooring, remove the old flooring and then prepare the subfloor.

To complete preparations for the car¬pet installation, remove floor register covers and, if you want it to cover the carpeting, quarter-round baseboard molding. Fill in any wide cracks in the floor with wood putty, smoothed over with a putty knife, and let the patches dry completely. Vacuum the room thoroughly before you start.

Read More…

Installing carpeting takes preparation and care, but it doesn’t take much special skill. Very large rooms require power stretchers, so leave those to the professionals-the rest of the house is yours.

Tools: measuring rule, hammer, nail set, screwdriver, putty knife, vacuum cleaner, work gloves, tack hammer, ¼ -inch-thick piece of scrap wood, small handsaw, heavy scissors, staple gun, paintbrush or fine-toothed notched trowel, utility knife with sharp heavy-duty blades; knee kicker, available on rental from most carpet dealers; block of scrap wood, plane.

Materials: graph paper, flooring nails, wood putty, tack-less carpet fastening strips, metal door edging strip for each doorway in room, latex or vinyl foam carpet padding, foam padding adhesive, heavy-duty staples, precut and preseamed carpeting. Time: 1 to 2 days, depending on preparation necessary.

Probably the most difficult part of installing carpeting is calculating exactly what to buy and how to place it. Car¬peting is sold in 9-foot, 12-foot, and 15-foot widths; padding is sold in standard 4 ½ -foot rolls. Before you buy, measure the room to be carpeted and draw a floor plan on graph paper make sure your measurements are exact. Mark the exact position and width of all doors, windows, fireplaces, radiators, and other wall interruptions, and include the full depth of door frames. Take this floor plan with you to the carpet dealer.

Plan the layout of the carpeting and the padding carefully with the dealer to take advantage of the full width of the carpeting and to minimize seaming in heavy-traffic areas. Calculate the square yardage to be carpeted-length times width, divided by 9-and take the dealer’s advice on the lengths of carpeting and padding you’ll need.

It is possible to cut and seam the carpeting yourself, but this can be tricky. In a small room, no wider than the carpet roll, you won’t have to make seams; otherwise, have the carpet dealer cut and seam the carpeting to fit the room.
The dealer should also determine the amount and type of tackless strip fastener you need. The fastener comes in 4-foot strips.

The type depends on the thickness of your carpet and the floor you’re covering; the strips have preset edge tacks and preset nails for installation over wood or concrete. Be sure to buy the right kind, and buy a strip or two extra to allow for mistakes. Have metal door edging strips cut to the exact measure of your doors.

Finally, rent a knee kicker from the carpet dealer. The kicker is used to stretch the edges of the carpet onto the fastening strips.

to be continue to: Install carpeting